Effect of bristle pack position on the rotordynamic characteristics of brush-labyrinth seals at various operating conditions

Over the last few decades, the research on the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals is not sufficient. To this end, two kinds of brush-labyrinth seals for the bristle pack element installed upstream of the labyrinth teeth named BSU and installed downstream of the labyrinth teeth called BSD were used to investigate the effect of bristle pack position on the rotordynamic characteristics of the brush-labyrinth seals. Using the numerical model combining the porous medium model and the whirling rotor method, the rotordynamic characteristics of the BSU and BSD at various operating conditions including four kinds of pressure ratios, five kinds of inlet preswirl speeds and four kinds of rotor spinning speeds were conducted. The obtained results show that the effects of operating conditions on rotordynamic coefficients for the different seal configurations are different. The direct stiffness, cross-coupled stiffness and direct damping of the BSU are lower than those of the BSD. The rotordynamic coefficients of the BSU are more insensitive to the operating conditions variation. From the perspective of the seal stability, the BSU is a better brush-labyrinth seal configuration at high pressure ratio, high positive preswirl or high rotor spinning speed conditions. While in the case of low pressure ratio, low positive preswirl or low rotor spinning speed conditions, the BSD is a better choice.     

沉井技术在码头改造工程中的应用

沉井依靠自重消除刃脚阻力和外壁摩擦力下沉,本文对该项工艺的下沉、纠偏、挖土、封底主要技术问题进行介绍。     

Modelling of Ejecta as a Space Debris Source

When a micro-debris or a micrometeoroid impacts a spacecraft surface, a large number of secondary particles, called ejecta, are produced. These particles can contribute to a modification of the debris environment: either locally by the occurrence of secondary impacts on the components of complex and large space structures, or at great distance by the formation of a population of small orbital debris. This paper describes firstly, the ejecta overall production, and secondly, the lifetime and the orbital evolution of the particles. Finally the repartition of ejecta in LEO is computed. Some results describing the population as a function of size and altitude are presented.     

二次成像法在风洞模型自由飞运动记录中的应用

风洞模型自由飞是一种无支杆干扰的非接触式气动特性测量方法。为获得相对于实验室固定坐标系的精确的模型姿态和位置测量值，必须在成像照片中有固定坐标系框架标志的清晰影像。本文描述了在高超声速脉冲风洞中模型自由飞运动记录中二次成像法的应用。以０．１ｍｍ细线所构成的正交实验室固定坐标框架置于模型运动记录的第一次成像面上，然后用高速鼓轮相机记录模型自由飞相对于坐标系运动的清晰照片，从而获得模型在高超声速（Ｍ＿∞＝９．９）流动条件下的静、动稳定性导数的有效结果。     

高压输电网设计中的二阶非线性方程的次谐波分枝

本文用Melnikov方法研究高压输电网设计中提出的非线性二阶受迫振动方程的次谐波分枝,分析了系统可能出现次谐解的条件和参数区域,以此为工程应用提供参考。     

碳粉燃料在火箭冲压发动机补燃室内燃烧特性的分析

采用概率密度函数(PDF)及确定轨道模型数值模拟一种环向进气的固体火箭冲压发动机补燃室气固两相流的掺混燃烧,考虑固体颗粒直径大小和补燃室长度对燃烧效率的影响。结果表明:增大固体颗粒直径,燃料的燃烧效率明显减小;增大补燃室长度,燃料的燃烧效率增大。     

多级串联密封系统泄漏规律及应用研究

多级串联密封结构的泄漏过程非常复杂,其泄漏规律对多级密封结构的设计、检漏和密封安全评估等具有重要意义。建立了多级串联密封系统的数学模型,揭示了多级串联密封结构正压泄漏的漏率、漏量与泄漏时间关系的一般规律,通过三级密封系统泄漏的仿真计算实例和泄漏实验,验证了多级串联密封泄漏理论的正确性,并总结了多级串连密封泄漏规律的应用方法。     

燃气推力矢量控制发动机内流场数值模拟

采用基于Favre平均的三维N-S方程,对燃气推力矢量控制发动机全内流场进行了数值仿真,研究了燃气引流、燃气二次喷射及与发动机内主流相互作用等复杂流动。研究结果表明,流场内包含复杂的涡系结构和波系结构,还存在着边界层与激波的相互干扰、自由剪切层、激波、膨胀波和大尺寸分离。通过数值模拟,对试验中的异常现象进行了定性分析,得出了与试验一致的结论。     

导弹密封皮碗的可靠寿命试验与评估

对某型号导弹密封系统所用的橡胶材料进行了加速老化试验，通过分析给出贮存可靠及可靠寿命等性能指标随时间、温度的变化规律。并引进随温度变化的失效率与加速系数，来研究材料对贮存温度的敏感性，从而为确定最佳贮存温度提供依据。     

考虑二次流影响的压缩系统稳定性模型

利用Ａｄｋｉｎｓ－Ｓｍｉｔｈ二次流模型计算得到转子出口截面落后角沿叶高的变化。在压缩系统稳定性模型中考虑叶尖流面落后的角影响，并提出一个新的时滞参数计算公式，计算结果表明，落后角的大小对压缩系统的稳定性影响很大，同时揭示了叶尖间隙对压缩系统稳定性的影响。